Bueno, nuevamente yo, agradezco la pagina fue de un apoyo impresionante, consistente y directa. Gracias. Ingrese a la configuracion del ap como se indica y se cambio la ip a 10.0.0.1 mascara 255.255.255.0. Desconecto el ap despues de guardar la configuracion y le conecto un cable directo por ethernet, responde ping a la direccion 10.0.0.1 pero cuando ingreso por el navegador (internet explorer 9) no me devuelve la configuracion via web. Puedes por favor ayudarme con eso. Gracias nuevamente por el apoyo.
Pos data: anexo las lineas al ap que configure por hyperterminal con el rollover
Xmodem file system is available.
flashfs[0]: 150 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 4999680
flashfs[0]: Bytes available: 2741760
flashfs[0]: flashfs fsck took 17 seconds.
Reading cookie from flash parameter block...done.
Base ethernet MAC Address: 00:1f:ca:64:76:aa
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
link auto-negotiating....
auto-negotiation takes 10000 milli-seconds to complete
ERROR: timeout waiting for auto-negotiation to complete
ERROR: fail to bring ethernet link up
The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:
ether_init
tftp_init
boot
Loading "flash:/c1200-k9w7-mx.123-8.JEB/c1200-k9w7-mx.123-8.JEB"...#############
################################################################################
################################################################################
################################################################################
################################################################################
###########################
File "flash:/c1200-k9w7-mx.123-8.JEB/c1200-k9w7-mx.123-8.JEB" uncompressed and i
nstalled, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8)JEB, RELEASE S
OFTWARE (fc2)
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 27-Apr-07 00:59 by hqluong
Image text-base: 0x00003000, data-base: 0x00698FC0
Initializing flashfs...
flashfs[1]: 150 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 4999680
flashfs[1]: Bytes available: 2741760
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision A0) with 15138K/12
36K bytes of memory.
Processor board ID FOC12185UJT
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from power-on
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1F:CA:64:76:AA
Part Number : 73-8704-14
PCA Assembly Number : 800-23211-14
PCA Revision Number : A0
PCB Serial Number : FOC12185UJT
Top Assembly Part Number : 800-29026-01
Top Assembly Serial Number : FTX1223R0E2
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-A-K9
Press RETURN to get started!
*Mar 1 00:00:05.388: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self t
est passed
*Mar 1 00:00:06.596: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self
test passed on interface Dot11Radio 0
*Mar 1 00:00:08.689: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:08.691: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:08.818: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Mar 1 00:00:08.972: %SYS-5-CONFIG_I: Config
ap>enaqb
Translating "enaqb"...domain server (255.255.255.255)ured from memory by console
*Mar 1 00:00:08.972: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8)JEB, RELEASE S
OFTWARE (fc2)
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 27-Apr-07 00:59 by hqluong
*Mar 1 00:00:08.973: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a c
old start
*Mar 1 00:00:09.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to down
*Mar 1 00:00:09.818: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Mar 1 00:00:09.901: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:20.830: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:21.830: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to down
% Unknown command or computer name, or unable to find computer address
ap>
ap>
ap>
ap>enable
Password:
ap#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
ap(config)#interface bvi1
ap(config-if)#ip address 10.0.0.1 255.255.255.0
ap(config-if)#end
ap#wr
*Mar 1 00:02:46.333: %SYS-5-CONFIG_I: Configured from console by console
Building configuration...
[OK]
ap#
